【超频】新手必须保存的资料 EP45―UD3系+E8200超4G的BIOS设置

fei513

新手必须保存的资料 EP45-UD3系+E8200超4G的BIOS设置

******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [A]
CPU Clock Ratio ......................: [8X]
x Fine CPU Clock Ratio................: +0.0
CPU Frequency ........................: 4.096GHz( 512X8)

********** Clock Chip Control ********

>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [512]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]

>>>>> Advanced Clock Control..........: [Press Enter]
CPU Clock Drive.......................: [800mV]
PCI Express Clock Drive...............: [900mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 0ps]

******** DRAM Performance Control ********

Performance Enhance...................: [Standard]
Extreme Memory Profile(X.M.P.)........: [Disabled]
(G)MCH Frequency Latch................: [Auto]
System Memory Multiplier (SPD)........: [2.00D]
Memory Frequency(Mhz).....800.........: 1024
DRAM Timing Selectable (SPD)..........: [Manual]

>>>>> Standard Timing Control
x CAS Latency Time................5...: [ 5]
x tRCD ...........................5...: [ 5]
x tRP.............................5...: [ 5]
x tRAS...........................18...: [15]

>>>>> Advanced Timing Control.........: [Press Enter]
x tRRD............................3...: [ 3]
x tWTR............................3...: [ 3 (11 in Windows)]
x tWR.............................6...: [ 5 (14 in Windows)]
x tRFC...........................52...: [54]
x tRTP............................3...: [ 1 (4 in Windows)]
x Command Rate (CMD) .............0...: [ 2]

>>>>> Channel A Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [11]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto

x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto

x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto

>>>>> Channel A Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]

x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto

x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto

>>>>> Channel B Timing Settings.......: [Press Enter]
x Static tRead Value.............10...: [11]
x tRD Phase0 Adjustment...........0...: Auto
x tRD Phase1 Adjustment...........0...: Auto
x tRD Phase2 Adjustment ..........0...: Auto
x tRD Phase3 Adjustment...........0...: Auto

x Trd2rd(Different Rank)..........6...: Auto
x Twr2wr(Different Rank)..........6...: Auto
x Twr2rd(Different Rank)..........5...: Auto
x Trd2wr(Same/Diff Rank)..........8...: Auto

x DIMM1 Clock Skew Control (ps).......: Auto
x DIMM2 Clock Skew Control (ps).......: Auto
x DDR Write Training..................: Auto

>>>>> Channel B Driving Settings......: [Press Enter]
x Driving Strength Profile............: [1066MHz]

x Data Driving Pull-Up Level..........: Auto
x Cmd Driving Pull-Up level...........: Auto
x Ctrl Driving Pull-Up Level..........: Auto
x Clk Driving Pull-Up Level...........: Auto

x Data Driving Pull-Down Level........: Auto
x Cmd Driving Pull-Down level.........: Auto
x Ctrl Driving Pull-Down Level........: Auto
x Clk Driving Pull-Down Level.........: Auto

****** Motherboard Voltage Control ******

Voltage Types..........Normal...........Current
-----------------------------------------------
>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore..............1.27500V.......: [1.4V (1.38V in Windows)]
CPU Termination........1.200V.........: [1.300V]
CPU PLL................1.500V.........: [1.65V]
CPU Reference..........0.760V.........: [.76 (.7 when VTT is 1.2)]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.380V]
MCH Reference..........0.760V.........: [.72]
MCH/DRAM Reference.....0.900V.........: [1.05]
ICH I/O................1.500V.........: [1.5V]
ICH Core...............1.100V.........: [1.1V]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.12V (2.11 in Windows)]
DRAM Termination.......0.900V.........: [1.05]
Channel A Reference....0.900V.........: [1.05]
Channel B Reference....0.900V.........: [1.05]

******** Advanced BIOS Features ********
No-Execute Memory Protect.............: [Enabled]
CPU Enhanced Halt (C1E)...............: [Disabled]
C2/C2E State Support..................: [Disabled]
x C4/C4E State Support................: Disabled
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.....................: [Disabled]
Virtualization Technology.............: [Disabled]
Delay For HDD (Secs)..................: [ 0]
Full Screen LOGO Show.................: [Disabled]
Init Display First....................: [PEG]

******** Integrated Peripherals ********
USB Keyboard Function.................: [Disabled]
USB Mouse Function....................: [Disabled]
USB Storage Function..................: [Disabled]